WT Forums

HELP do u know where i can find a part# for the small jack pad recepticles in the wheel pod. Ive looked in the 51 and 32 nothing and im going nuts

get muddy

Give me about 15 minutes and I will have it for you..with TO ref.

Ugly but well hung!
http://www.warthogpen.com

<BLOCKQUOTE id=quote><font size=1 face="Verdana, Arial, Helvetica" id=quote>quote:<hr height=1 noshade id=quote>
HELP do u know where i can find a part# for the small jack pad recepticles in the wheel pod. Ive looked in the 51 and 32 nothing and im going nuts

get muddy
<hr height=1 noshade id=quote></BLOCKQUOTE id=quote></font id=quote><font face="Verdana, Arial, Helvetica" size=2 id=quote>

It's going to take a little longer than I thought! As you said it's not in the -51 and I found today not on the pod drawings. I also went to the "Hog-up" wing shop but they couldn't help because they have never ordered these!

I have the SPO ES on it and should know something tomorrow. BTW do you need some? If so I may be able to get a set and ship them to you.

Ugly but well hung!
http://www.warthogpen.com

Have a jet here with a striped one (SP) its a flyable write up so it can go 04bq. just need the part # and ref. thanks

get muddy

<BLOCKQUOTE id=quote><font size=1 face="Verdana, Arial, Helvetica" id=quote>quote:<hr height=1 noshade id=quote>
Have a jet here with a striped one (SP) its a flyable write up so it can go 04bq. just need the part # and ref. thanks

get muddy
<hr height=1 noshade id=quote></BLOCKQUOTE id=quote></font id=quote><font face="Verdana, Arial, Helvetica" size=2 id=quote>

OK we are looking inti it and I will get back to you.

Ugly but well hung!
http://www.warthogpen.com

Koobster are you active duty?

I've looked in the -51 and the 3-1 and you're right it's not there.
Without the T.O. Ref you'll play hell with the supply folks in getting it. If there it's not in the T.O. you can bet your life supply won't have it which means a pull off a AMARC jet. Since it's probably not stock listed, how's supply going to bill it?
Either Dice or AFETS if you're active duty can get you a drawing number to identify it, but better yet why not have your metals tech guys rethread it if possible or put a heli coil in it.
Getting a repair disposition from Depot will take a lot less time and headache.
Cheers
db

Being responsible means sometimes pissing people off.
Gen Colin Powell ret

thanks for the idea d.b. had metals tech put a heli coil in it. also found a part #on the bottem of it. no crosses for it though.
Yes Im active, TDY HERE

get muddy

<BLOCKQUOTE id=quote><font size=1 face="Verdana, Arial, Helvetica" id=quote>quote:<hr height=1 noshade id=quote>
thanks for the idea d.b. had metals tech put a heli coil in it. also found a part #on the bottem of it. no crosses for it though.
Yes Im active, TDY HERE

get muddy
<hr height=1 noshade id=quote></BLOCKQUOTE id=quote></font id=quote><font face="Verdana, Arial, Helvetica" size=2 id=quote>

Can you send me that part # so I can engage the ES with that info.

Ugly but well hung!
http://www.warthogpen.com

emailed it to you

get muddy

Edited by - koobster on Nov 24 2003 1:12 PM

Edited by - koobster on Nov 24 2003 1:15 PM

No problem Koobster.
Been down that road many a time on the Hawg.
Cheers and good luck where ever you are.
db

Being responsible means sometimes pissing people off.
Gen Colin Powell ret